chinahorse92 – https://www.repairmywindowsanddoors.co.uk/redbridge-windowrepair/

Replacing uPVC Window HandlesThe replacement of window handles made of upvc is a simple task. The most important thing is to make sure that the new handle is a good fit for the spindle carved out in the window mechanism.If you follow the steps below any cockspur handle can fit in most windows. The step height of the handle is crucial.What to look forMany of the windows in the UK are fitted with uPVC handles Over time, they will begin to show signs of wear and tear. The handle on the window can become loose or difficult-to-operate when this occurs. Anyone who is proficient working with basic hand tools can accomplish this fairly simple job.The first step is to make sure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the screws or pins that secure the handle in place. These are typically located on the inside of the handle. They can be removed with a screwdriver, or pliers.Once the handle has become loose, it can be removed from its hinges by gently pulling off. It is then necessary to locate a replacement handle of the same style and size. This can be accomplished online or at an area DIY store, and the process should only take about five minutes with an screwdriver.The most important thing to consider when replacing the uPVC window handle is the step height. This is the distance between the handle’s base and where it is located in the window frame. This is typically a standard measurement, and it is crucial to examine the step height of your current handle prior to ordering the new one.There are several sizes depending on the kind of handle. Inline handles for uPVC windows generally have 31mm lug centres as well as handles with cockspur with 43mm centres. Tilt and turn handles are commonly found on uPVC windows, and they feature a specific design that allows the window to be slid up to allow for ventilation, and then turned to fully open the window.The most frequent breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This can make them hard to open and therefore it is essential to ensure that the replacement handle you buy has the same length of spindle as your existing one.Remove repairmywindowsanddoorsIf your window handles are damaged or not properly fitted, they could cause double-glazed windows to open and close incorrectly. They may even become stuck. This could be due to a number of reasons, including general wear and tear on the handle or corrosion. In these situations, it is important to find replacement window handles made of upvc as soon as possible in order to prevent further damage and loss of function.One of the first things to do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Begin by removing the screw with the handle when it is in a closed position. This should reveal another screw and once removed, you can then begin to remove the handle. You can make the job easier by using an electronic screwdriver.Be aware that screws could be hidden under caps made of plastic. It is best to remove the covers with the help of a Stanley knife. After removing the old handle, you’ll need to check the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is crucial as you’ll need to measure the length of the spindle of the old handle to ensure that it is in line with the size of the window mechanism and handle spindle that has been cut out.The different kinds of window handles made from upvc include: Espag handles, which feature a central screw that will turn left or right; Cranked handles, that have two screws and are used on tilt and turn windows made of upvc; and Spade handles, which have an arm that is flat and can be used on either side of the window. It is easy to replace the handle after you’ve identified one that is suitable. Simply screw it into place, and make sure the spindle is properly inserted into the lock mechanism. After that the handle should be secured to the window frame, and your new window handles made of upvc should be secure.Measure the SpindleIf you need to replace a handle made of upvc that has collapsed, it’s likely the spindle that holds it in place is damaged or is loose. In some cases this can be fixed using screws or pins to secure it. In some instances, it may be necessary to replace the handle. There are several different types of handles made of upvc. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each type of handle is mounted and replaced in a different manner.Before you purchase a new handle, it is essential to know the dimensions of the one you have. This will help ensure that the new handle is of the correct size and fits within the window. All handles are calibrated according to industry standards, so it is easy to find the correct size.To determine the size of your handle first remove it from the window by turning it to the open position. You should then be able to see the size of the screw or pin that secures it. Use a ruler or tape measure to determine how long the spindle is. Once you have the length of your spindle, it is possible to buy a replacement of the exact same length.When you are looking to replace a handle you should take into consideration the step height of an upvc window handle. The step height is measured from the base to the point at which the handle is positioned on the frame. In general, this is around 21mm for uPVC windows, and 9mm for aluminium. To be sure that the new handle is suitable it, you can drop something in the gap to determine how far it goes before it meets an obstruction.Cockspur handles typically have different backset heights, based on the style of window they are placed in. Inline Espag handles have a standard height of 43mm centre to centre (2 fixing points). Cockspur handles, however, have different backset heights according to the style of the window they’re in. This is due to the fact that they have a spur that extends from the handle and locks over a cockspur wedge striker plate.Install the New HandleAfter you have chosen the new handle, ensure that it is aligned with the screw holes on the door. Secure it using the screws provided. Install the latch lever the same way as the handle on the main handle if you are also replacing the door handle. After that, attach the door trim to hide the screws for mounting.Tips: To take the metal head from the wedge made of wood Hold the handle so that its broad end rests on the floor. Use a hammer to tap on the thin end of the handle. Be careful not to scratch the handle or the handle spindle.