skiingblow73 – https://www.repairmywindowsanddoors.co.uk/chiswick-windowrepair/

How to Replace Door HandlesDoor handles are a crucial part of the decor of your home. A new handle will elevate your home and bring your decor to the present.Over time, your door knobs may become stiff, or even break. These are signs it’s time to replace them. This guide will help you select the correct door handle replacement for your home.Door KnobsDoor handles enhance the look of your home, while making it easier for people to open and close doors. They are available in a variety of finishes, colors and types to complement your decor. If yours is beginning to show signs of wear or requires an upgrade, you can replace them in a couple of simple steps.You’ll need to find the shaft, or spindle through which the knob is inserted to the door. Some have a tiny hole that you can put an incredibly small screwdriver to remove the set screws holding the knob in place. Some have a small slot or hole where can be used with a flathead screwdriver to push on a spring-activated pin called a detent. When you press this pin and the latch mechanism opens, it releases and lets you pull or push the knob.Once you have the spindle or shaft in your hand, remove the old knob and replace it. Align it correctly and check that the latch functions properly before tightening the set screws.Once you’ve replaced the knob, hold the rod of the latch over the hole in the door and lock it in place with the rod mechanism on the second knob. Make sure the holes are aligned then tighten the screws for the latch plate.Some prefer the smooth or brushed finish on their door hardware to give it a sleek, contemporary look that matches other furnishings in their homes. Others prefer a more rustic design, which pairs well with farmhouse-styled spaces. If you have a member of your family who has mobility issues, you might prefer an rim or lever lock, which requires less pressure to operate.While aesthetics have traditionally been the most important factor in door handle design, other factors are increasingly being considered too. Accessibility and control of infections have been key issues when it comes to developing new designs for handles. For instance certain handles can be operated using the arm of a person.LatchThe latch that holds the door handle open can wear down over time. It is simple to change the latch on your door handle. This will make huge differences in how it opens and closes.Depending on the type of handle you are using the latch may be a separate piece or a part of the knob. In either case, you will follow the same process for removing and replacing. It’s simple to remove the old latch, especially in the case of an entry handle that has a “magic” button. This tiny pressure-slot, found on the side knob is what you need to press in order to remove the latch of the handle.If your handle doesn’t have this button, the first step is to remove any cover plates that are positioned over the latch plate. They are typically rectangular or circular and can be removed with a screwdriver. Some have a slot in which you can put your screwdriver. Other handles just snap off.The next step is to remove the two machine screws that secure the latch and inner plate to the door handle. You will need to store these shorter screws with sharp tips in a secure location to be able to reuse them later. Once the screws are removed you can remove the latch plate and mechanism out of the hole in the door and put it away.Now you can start on the new latch. Install the latch plate into the door hole and secure it using the hardware supplied. Make sure the square pin on the inside of the latch is facing the latching mechanism inside the handle and that it lines up with the other screw chambers of the door handle. Then push the exterior latch plate onto the handle and secure it with the screws supplied.Strike PlateIt is common to replace a door handle when it feels loose, or does not lock properly. This is often due to malfunctioning components of the latching mechanism, such as the strike plate being too small or shifted upwards or downwards on the doorjamb with time. This project allows you replace your old strikeplate with an extended one, which will offer better security for your door and will keep it shut.Apply some lipstick or other marking material on the bolt for the latch to determine if it’s the strike plate. Close the door and try to latch it. If the mark is below the strike plate hole this indicates that your door won’t latch due to the fact that the strike plate is too small. If the mark is above the strike hole on the plate, it’s likely that the strike plate has been moved upwards or downwards on the doorjamb.Depending on the door you have You may be able to just attach the new strike plate in place over the old one with the screws included with it. You may need to drill holes first and then chisel some wood out to ensure a tight fit. If this is the case, be careful not to cut too hard or you’ll ruin the strength of your doorjamb.Installing a brand new box-style strike plate will give the lock a stronger grip on doors and require more force to open them. Typically check over here will require two longer screws to secure the strike plate to the frame of the door. You’ll need remove the previous strike plate, then drill and chisel the wood to make room for the new one.This difficult-to-find strike plate was designed to be used with antique rim locks, and it’s constructed of robust solid brass with an extremely thick. It comes with both machine screws and wood screws, so you’ll have the correct hardware for your job. Make sure to note that wood screws have a sharp edge, whereas the machine ones are more blunt.